Table of Contents
Wireless Rain-Clik™ – Installation Instructions Remove the sensor jumper across the two SEN terminals in the controller. Attach the two yellow wires to the 24 VAC terminals. Attach the blue wire to one SEN terminal and the white wire to the other SEN terminal.
Why is my rain sensor not working?
The most common reason is because the sensor has NOT received enough rain to activate. The rain sensor switch is in the “BYPASS” or “OFF” position. To fix this, slide the switch into the “ACTIVE” position. During installation of the rain sensor, the terminal jumper was NOT removed.
How much does it cost to install a rain sensor?
A: On average, cost for the sensors runs $18 to $40 and installation runs $125 to $150.
How do you bypass a hunter rain sensor?
Simply turn the dial to RUN (BYPASS SENSOR) and the weather sensor will be overridden. The wireless rain sensor may be bypassed by using the built-in bypass feature on the receiver. To bypass the sensor, press the SENSOR BYPASS button on the receiver. The bypass status light will turn red when the sensor is bypassed.
How do you adjust Hunter rain sensors?
The Mini Clik uses a spindle adjustment to set the amount of rain you want the sensor to witness before it shuts down the system. This amount can be set by adjusting the spindle on top of the sensor and the range is 1/8″ (3.17mm) to 1″ (25.4mm).
What should I set my rain sensor to?
IFAS researchers recommend rain sensor thresholds of 1/4” for 2 or 3 day per week irrigation with no more than 1/2” for 1 day per week irrigation. Remember, the lower the setting, the more water saved.
How do rain sensors work?
The rain sensor works on the principle of total internal reflection. An infrared light beams at a 45-degree angle on a clear area of the windshield from the sensor inside the car. When it rains, the wet glass causes the light to scatter and lesser amount of light gets reflected back to the sensor.
How long does a rain sensor last?
How long do rain sensors last? The average rain sensor only functions for 3-5 years before needing replacement.
How do you troubleshoot a rain sensor?
Rain Sensor Problems? Make sure it’s wired correctly. Test for continuity. If you’re not savvy with a multimeter, when its dry outside turn on a zone within sight of the sensor. Location. Make sure the cap and spindle is pointing toward the sky! Sensitivity and dry time adjustments. Check for debris and disc condition.
Is a rain sensor worth it?
These components detect the level of moisture present and automatically stop the sprinklers from running when watering isn’t necessary. By doing so, the sensors help you save money on water. So, you may end up wasting water instead of saving money. For many homeowners, installing both rain and soil sensors makes sense.
Where should I put my rain sensor?
The most important aspect of installing a rain sensor is where to place it. It should be installed in an area that is unobstructed by trees, roof over hangs, or anything else that might block rain from getting to the sensor. If it is a wired sensor, placement is generally near the sprinkler controller.
Can I install rain sensing wipers?
Install the sensor sticker to the outside of your windshield. This is the sensor itself, and it will not be able to detect rain if it is facing the inside of the vehicle. Depending on what type of rain sensor you have purchased, the windshield might need to be taken out before you can place the sensor.
What is sensor bypass on Hunter?
Toggle switch that controls the input signal from the weather sensor (Rain-Clik, Freeze-Clik, Wind-Clik, etc). When the switch is set to “Bypass” the controller will ignore the signal from the sensor and irrigate normally. Support.
How do you turn off a rain sensor?
Deactivate the rain sensor by pressing the rain sensor button or moving the stalk switch up to another wiper program. The rain sensor is deactivated automatically in ignition position 0 or when the engine is switched off.
What does sensor bypass mean on a sprinkler system?
The sensor override, or bypass switch, on a controller lets you turn off the sensor so you can resume irrigation. This is especially useful when troubleshooting a system. In most cases, you simply move the sensor override switch to off.
How do you add a sensor to Hydrawise?
To configure a sensor in the Hydrawise software, follow the steps below. Click the ( ) icon in the upper left. Create a new sensor by clicking ADD SENSOR TO CONTROLLER. Choose the SENSOR NAME. Choose the type of sensor (most Hunter sensors are normally closed). Change the controller input to SEN. Click NEXT.
Does Hunter rain sensor have a battery?
The Wireless Rain-Clik™ transmitter is designed to operate up to ten years with it’s sealed, maintenance-free battery.
How does rain drop sensor works?
Raindrop sensor is basically a board on which nickel is coated in the form of lines. When rain drop present it reduces the resistance because water is a conductor of electricity and presence of water connects nickel lines in parallel so reduces resistance and reduces voltage drop across it.
What is the uses of rain sensor?
The primary purpose of rain sensors is to conserve water by detecting natural rain and turning off the sprinklers. When there is enough rainfall, the irrigation and sprinkler systems will stop automatically. As a result, water wastage will be reduced.
What does Rain Bird rain sensor do?
The Rain Bird RSD Series Rain Sensor automatically shuts off your sprinkler system when it rains, so you don’t have to worry when you’re home or away. The RSD Series Rain Sensor easily connects to most irrigation system controllers.
How much water does a rain sensor save?
A rain sensor saves an average of 10% of irrigation water usage. As we strive to become more responsible with our resources, it just makes sense for every irrigation system to be equipped with one. Beyond simple rain sensors, more advanced technology has become widely available that can conserve even more water.
How do you test a rain sensor?
Turn on the time clock for the zone nearest the sensor. Press and hold down the button on top of the sensor. The zone should shut off. (If your rain sensor does not have a button on top, it is not a cork-disc sensor)Jan 5, 2021.
